Cisco Cheap SFP-10g-Sr Compatible 10g SFP+ Transceiver Module 850nm 300m with ce certificate top quality low price

Product Description

Cisco SFP-10G-SR compatible 10G SFP+ Transceiver module 850nm 300m

1.Feature:

1. Hot-pluggable SFP+ footprint;
2. Supports rate selectable 1.25 Gb/s Or 9.95 to 10.3 Gb/s bit rates;
3. CZPT  dissipation < 1W;
4. RoHS-6 compliant ( lead-free );
5. Single 3.3V CZPT supply;
6. CZPT imum link length of 300m on2000 MHZ-km MMF;
7. Uncooled 850nm VCSEL laser;
8. Receiver limiting electrical interface;
9. Duplex LC Connector;
10.Built-in digital diagnostic functions;
11.Comerical temperature range0ºC to 70ºC;

2.Applications:

1.1000BASE-SX 1G Ethernet;
2.10GBASE-SR/SW 10G Ethernet;
3. CZPT  optical links;

3.Description:

This 1G/10G Dual-Rate SFP+ transceivers are designed for use in 1-Gigabit and 10-Gigabit Ethernet links over multimode fiber. They are compliant with SFF-8431, IEEE 802.3-2005 10GBASE-SR/SW and 1000BASE-SX. Digital diagnostics functions are CZPT via a 2-wire serial interface, as specified in SFF-8472. The GPP-85192-SRCM is a “limiting module”, i.e., it employs a limiting receiver. Host board designers using an EDC PHY IC should follow the IC manufacturer’s recommended settings for interoperability with an SFP+ limiting module. This product is for applications specifically designed for 10G SFP+ ports and 1G/10G SFP+ ports and not native 1G SFP ports. The transceiver is RoHS compliant and lead free per Directive 2002/95/EC5.

4.Absolute CZPT imum Ratings:

These values represent the damage threshold of the module.  Stress in excess of any of the individual Absolute CZPT imum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within CZPT mmended Operating Conditions.
 

Parameters Symbol Min. Max. Unit
Supply Voltage VCC -0.5 +3.6 V
Storage Temperature Tc -40 +85 °C
Operating Case Temperature Tc 0 +70 °C
Relative Humidity RH 0 85 %

5.Recommended Operating Conditions:
 

Parameter Symbol Min. Typical Max Unit
Supply Voltage VCC 3.0 3.3 3.6 V
Supply current Icc   200 300 mA
Operating Case Temperature TC 0 25 70 °C
Module CZPT Dissipation Pm 0.7 1 W

Notes:
[1] CZPT current is shared between VCCTX and VCCRX.
[2] In-rush is defined as current level above steady state current requirements.

6.Electrical characteristics(TOP = 0 to 70ºC, VCC = 3.14 to 3.46 Volts):
 

      Parameter Symbol Min. Typical Max Unit Ref.
Supply Voltage VCC 3.14   3.46 V  
Supply Voltage Icc     250 mA  
    Transmitter
Input differential impedance Rin   100   Ω 1
Differential data input swing Vin,pp 180   700 mVpp 2
Transmit Disable Voltage VD 2   VCC V  
Transmit Enable Voltage VEN Vee   Vee+0.8 V  
    Receiver
Output differential impedance Rout   100   Ω  
Differential data output swing Vout,pp 300   700 mV 3
Data output rise time, fall time tr 28     ps 4
LOS Fault VLOS fault 2   VCCHOST V 5
LOS Normal VLOS norm Vee   Vee+0.8 V 5
Power CZPT Noise Tolerance VccT/VccR Per SFF-8431 Rev 3.0 mVpp 6

Notes:
1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
2. Voltage swing for 1G operation is equivalent to voltage swing in 10G operation (SFF-8431 Rev3.0).
3. Into 100Ω differential termination. Voltage swing for 1G operation is equivalent to voltage swing in 10G operation (SFF-8431 Rev 3.0).
4. 20-80%. Measured with Module Compliance Test Board and OMA test pattern. Use of four 1’sand four 0’s in sequence in the PRBS^9 is an acceptable alternative. SFF-8431 Rev 3.0
5. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board.
Normal operation is logic 0; loss of signal is logic 1. CZPT imum pull-up voltage is 5.5V.
6. Testing methodology per SFF-8431. Rev 3.0

7.Optical characteristics for RS0 = LOW (1G Operation):

(TOP = 0 to 70ºC, VCC = 3.14 to 3.46 Volts)

      Parameter Symbol Min. Typical Max Units Ref.
    Transmitter
Average Launch CZPT PAVE -9.5   -1 dBm 1
Optical Wavelength λC 840 850 860 nm 2
Rise-Fall Time Trise/Tfall     0.26 ns 3
RMS Spectral Width Δλrms     0.45 dB  
Average Extinction Ratio ER 9     dB  
Average Launch CZPT of OFF Transmitter POFF     -30 dBm  
Eye Mask   Compliant with IEEE 802.3
Tx Jitter Txj
Relative Intensity Noise RIN     -117 dB/Hz  
    Receiver
Wavelength Range λC 840   860 Nm 2
Receiver CZPT tivity RSENS -17     dBm  
Stressed Receiver CZPT tivity 50 μm MMF SRS50um     -13.5 dBm 4
Stressed Receiver CZPT tivity 62.5 μm MMF SRS62um     -12.5 dBm 4
Maximum Input CZPT PMAX +0.5     dBm  
Return Loss Rrx 12     dB  
LOS De-Assert LOSD     -18 dBm  
LOS Assert LOSA -30     dBm  
LOS Hysteresis   0.5     dB  

Notes:
1. CZPT is equivalent to 10G max spec.
2. This product has not been designed to support 780-nm laser operation.
3. 20%-80%.
4. Per IEEE 802.3-2005. 9dB extinction ratio transmitter.

8.Optical characteristics for RS0 = HIGH (10G Operation):

(TOP = 0 to 70ºC, VCC = 3.14 to 3.46 Volts) 

      Parameter Symbol Min. Typical Max Units Ref.
    Transmitter
Average Modulation Amplitude(OMA) POMA   -1.5   dBm 1
Average Launch CZPT PAVE -5   -1 dBm 2
Optical Wavelength λC 840 850 860 nm 1
RMS Spectral Width Δλrms     0.45 dB 1
Average Extinction Ratio ER 3.5     dB  
Average Launch CZPT of OFF Transmitter POFF     -30 dBm  
Eye Mask   Compliant with IEEE 802.3
Tx Jitter Txj
Relative Intensity Noise RIN     -117 dB/Hz  
    Receiver
Wavelength Range λC 840   860 Nm  
Receiver CZPT tivity(OMA)@10.3Gb/s RSENS1     -11.1 dBm 3
Stressed Receiver CZPT tivity (OMA) @ 10.3Gb/s RSENS2     -7.5 dBm 4
Maximum Input CZPT PMAX +0.5     dBm  
Return Loss Rrx 12     dB  
LOS De-Assert LOSD     -18 dBm  
LOS Assert LOSA -30     dBm  
LOS Hysteresis   0.5     dB  

Notes:
1. Per CZPT off Table 52.8, IEEE 802.3-2005
2. Average CZPT figures are informative only, per IEEE802.3-2005.
3. Measured with worst ER; BER<10-12; 231 – 1 PRBS.
4. Per IEEE 802.3-2005.

General Specifications

      Parameter Symbol Min. Typical Max Units Ref.
Bit Rate (RS0 = LOW) BR   1.25   Gb/s 1
Bit Rate (RS0 = HIGH) BR 9.95 10.3   Gb/s 2

 

      Parameter Symbol Max. Supported Distance Units
Distance @1G @10G
Fiber Type 850nm OFL Bandwidth        
62.5µm 160 MHz-km Lmax 220 26 m
  275 33
50µm 400 MHz-km Lmax 500 66 m
OM2 500 MHz-km 550 82
OM3 2000 MHz-km >550 300

Notes:
1. 1000BASE-SX. Tested with a 27 – 1 PRBS. See Section I, Note 5 for RS0 conditions for 1.25Gb/s operation.
2. 10GBASE-SR/SW. Tested with a 231 – 1 PRBS. See Section I, Note 5 for RS0 conditions for 10.3 Gb/s operation.

9.Our item and workshop:

10.Company Information:

Takfly, established in 2000, has been manufacturing and exporting fiber cable, adapter, attenuator, connector, coupler, splitter, termination box, ODF, fiber instruments, media conceiver, switch, optical module, CWDM/DWDM, etc. CZPT ‘s products have passed the management verification: ISO14001: 2004. and goods have passed RoHS, CE, FCC, CZPT , EN5571, ISO9001, etc.

So far, Our products have been widely installed in many big CZPT project and work perfectly. Many project contactors ask the first and CZPT operators to purchase fiber items from CZPT for their new project. In addition, we also have builted CZPT term cooperation with Lapp, Amper, Telefonica, orange and CZPT sson. All enquiry are warmly welcomed here no matter it’s small or big, we promise to provide all CZPT ers high quality and good price item.

Our sfp module can be produced compatible with HP, CSICO, CZPT , H3C and other devices. Welcome your trial order!